Re: Bad mast raising experience

From: Nancy E. Wigal (newigal@hotmail.com)
Date: Mon Apr 10 2000 - 07:23:31 PDT


- - - - - - - - - - - - - - - - - - - - - - - - - - -
        West Wight Potter Mailing List maintainer
                dfarrell@ridgecrest.ca.us
           List hosted by www.tscnet.com
- - - - - - - - - - - - - - - - - - - - - - - - - - -
thanks. My baby stays might be a little too loose. That's one thing I can
easily fix right now. As for the plate, it's pretty well bent and twisted. I
don't think I want to re-heat it and trust it afterwards. Mr. Murphy and his
laws may just kick in.

Thanks for your tips,

nancy

----Original Message Follows----
From: SolarFry@aol.com
To: newigal@hotmail.com
CC: wwpotter@tscnet.com
Subject: Re: Bad mast raising experience
Date: Mon, 10 Apr 2000 09:54:47 EDT
MIME-Version: 1.0
Received: from [205.188.157.42] by hotmail.com (3.2) with ESMTP id
MHotMailBABB282C0032D820F399CDBC9D2A96CC1; Mon Apr 10 06:54:54 2000
Received: from SolarFry@aol.comby imo-d10.mx.aol.com (mail_out_v25.3.) id
i.61.2abb7bf (3860);Mon, 10 Apr 2000 09:54:47 -0400 (EDT)
>From SolarFry@aol.com Mon Apr 10 06:58:28 2000
Message-ID: <61.2abb7bf.26233727@aol.com>
Content-Language: en
X-Mailer: AOL 5.0 for Windows sub 100

Chalk it up to inexperience and have no fear. It happens to the best sailors
in the world. So, hitch up that Potter and drag it where you want.

You might be able to find a good metalman with a welder that can heat and
straighten that mast base if it is not broken and is just bent... (I also
bent mine one time)

I have been a disabled sailor for over 5 yrs now. I use of only one hand to
lift mast while afloat, sometimes while underway, as I have a 12' bridge I
have to go under to get out to ocean. I am also a solo sailor...

I installed a second set of gudgeons 2" above the existing ones about 1/4"
to
right of them so I could use rudder and raise and lower mast while underway.
With second set of gudgeons rudder can remain on while mast support is
lifted
to its highest position prior to lifting mast. Someone else always help me
lift aft (rear) end of mast so it will slide aft while I position mast base
and step together. Then I insert that pin on aft end of mast base through
aft
end of mast step. I also changed 4 part pulley system to a 6 part pulley so
I would need less strength to lift mast. With this I am able to lift mast
while pulling with my good hand on the lifting line. I have never trusted
anyone to put that aft pin through mast base and step as this is a critical
part of lifting mast. Note that I also never put in the front pin as I find
it is redundant and will not help keep mast in place. this makes it easier
to
raise and lower as once mast is up and tuned there is pressure on that front
pin making it almost impossible to remove when you try to drop mast.
The baby shrouds (on the side they are shrouds - stays are fore and aft)
should be lightly lose (move back and forth no more than 1 1/2")

This url shows mast raising pretty well - check it out
http://www.trailersailor.com/widget/santana/Mastrais.htm (<A
HREF="http://www.trailersailor.com/widget/santana/Mastrais.htm">Mast
Raising</
A>)

There is another web site with a potter mast raising system. Maybe one of
the
guy/gals can find it and fwd it to you.

Good luck
SF

In a message dated 4/10/00 4:10:50 AM Pacific Daylight Time,
newigal@hotmail.com writes:

<< Had a mast raising disaster Friday. I was all set to take "Baydream,"
  my brand spanking new P19 out on her maiden voyage. Went on down to the
  marina and the dock boy offered to help me the raise the mast. Being 5"
  21/2" and 110 lbs., I accepted his offer, ASSUMING (you know what THAT
does)
  he knew how to step a mast.
>
  I rigged up the arrangement with the gin pole, line, etc., and told the
guy
  I was gonna haul away while he guided the mast STRAIGHT up, until the mast
  reached the point of easy hauling. Well, somehow he lost hold of the mast,
  and it flew straight over to the port side of the boat, severely bending
the
  mast step plate. I was sick with disappointment. I had several thoughts:
  kill the dock boy (not good), haul the boat over to either Dahlgren or Pax
  River and have the Navy practice guided missile exercises on it (just a
  brief thought, it left real quick), scream, cry or die. I did none of the
  above. I told the guy not to worry about it. He did seem genuinely
contrite.

  The mast is fine, and appears to have suffered no visible damage.
>
  I went over to BoatUS, conveniently located 15 minutes away and filed a
  claim. They called IM and reported it. Glenn called me when I got home
later
  that day, and confirmed I need a new mast step plate. It’s gonna be a
mess
  to replace the darn thing, because the plate is bolted to the bottom of
the
  mast with screws that disappear up inside the mast, of course. Looks like
  the rivets will need to be drilled out and the new plate attached, with
the
  bottom re-riveted. Glenn says those are stainless steel rivets and are
  probably not readily easy to replace with a hand-held rivet tool. Great.
>
  Lesson learned: don’t assume people who work at a marina full of sail
  boats know how to step a mast.
>
  What I now need is some help. Should the baby stays be taut? I have
  them loose. Since the mast raising rig is on the port side of boat, it
makes
  sense that the mast would want to travel to the left. Any thoughts, tips,
  suggestions or help on how to avoid this disaster in the future? I accept
  the fact I will always need assistance to step the mast. I have no problem
  with that. Unfortunately, I will almost always sail alone, so I will be
  canvassing the launch ramp for a willing volunteer. I have had some real
  serious thoughts about this boat now. I am scared to death to entertain
the
  notion of trailering the boat. I have this thought that the boat and mast
  have beaten me, that I’ll have to set it up at a marina in the permanent
  mast raised position, thus spoiling my dream of trailering this thing up
and
  down the length of the Chesapeake Bay, sailing at various locations. I
  really wonder if this boat is all that portable. Perhaps it is if I
  were a larger individual with more lead in my can, I don’t know.
>
  If any of you all out there can give me some constructive, positive
  feedback, I’ll take it. I’ve never rigged a sail boat like this
before. Not
  to criticize IM, but the owner’s manual leaves a lot to be desired. I
find
  it hard to believe that an individual who has never rigged a sailboat like
  this can take that book and successfully rig the vessel. Maybe it’s just
me.

  I’m pretty hard on myself right now, beating myself up and saying "If
  only this…, if only that…" which is no good.
>
  So, I feel a little bruised and battered right now, having to delay the
  maiden voyage of my boat. I even bought a bottle of cheap champagne to
POUR
  over the bow. (Don’t want to do that smashing thing across a fiberglass
  bow…just doesn’t work as well as the launchings I’ve seen down at
Newport
  News Shipbuilding and Dry-dock Company).
>
  Bottom line is, I’ll get over it. One day I’ll even laugh about it.
So,if
  any of you experienced Potter owners out there can give me some
advice,I’ll
  take it. Otherwise, I’m going to marina shopping for a slip real soon.
>
  Thanks for listening,
>
  Nancy E. Wigal
  HMS 1135 P19 "Baydream"
> >>

______________________________________________________
Get Your Private, Free Email at http://www.hotmail.com



This archive was generated by hypermail 2b29 : Sun Apr 30 2000 - 03:27:10 PDT